Your brake lights are essential for safe driving, signaling to other vehicles when you’re slowing down or stopping. A burnt-out brake light can not only be a safety hazard but also lead to a costly ticket. If you notice one of your brake lights isn’t working on your 2017 Subaru Crosstrek, it’s important to replace it promptly.
How to Change a Brake Light on a 2017 Subaru Crosstrek
This guide will walk you through the process of replacing a brake light on your 2017 Subaru Crosstrek. With a few simple tools and some patience, you can tackle this repair yourself and get your brake lights back in working order.
What You’ll Need
- Replacement brake light bulb (check your owner’s manual for the correct type)
- Small flathead screwdriver
- Gloves (optional)
## How To Change Brake Light On 2017 Subaru Crosstrek
A functioning brake light is crucial for your safety and the safety of others on the road. If one of your brake lights on your 2017 Subaru Crosstrek is burnt out, it’s important to replace it as soon as possible. Luckily, replacing a brake light bulb on a Crosstrek is a relatively straightforward process that most car owners can handle themselves with a few basic tools.
This guide will walk you through the steps of replacing a brake light bulb on your 2017 Subaru Crosstrek.
Gather Your Tools and Materials
Before you begin, make sure you have the following tools and materials on hand: (See Also: Which Is The Car Brake)
- Replacement brake light bulb (check your owner’s manual for the correct bulb type)
- Small flat-head screwdriver
- Gloves (optional, but recommended)
Locate the Brake Light Assembly
The brake light assembly is located on the rear of your Crosstrek, above the taillight. You’ll see two separate brake lights, one on each side of the vehicle.
Remove the Old Bulb
1. Open the trunk or hatch of your Crosstrek.
2. Locate the access panel for the brake light assembly. This panel is usually held in place by a few screws or clips.
3. Remove the screws or clips holding the access panel in place.
4. Gently pull the access panel away from the vehicle.
5. You will now see the brake light bulb. It is typically held in place by a retaining clip.
6. Carefully press down on the retaining clip and pull the bulb straight out of the socket.
Install the New Bulb
1. Align the new brake light bulb with the socket.
2. Push the bulb gently into the socket until it clicks into place. Make sure the bulb is seated securely.
3. Reinstall the retaining clip.
Reassemble the Brake Light Assembly
1. Replace the access panel and secure it with the screws or clips.
2. Close the trunk or hatch.
Test the New Bulb
1. Start your Crosstrek and turn on the brake lights.
2. Make sure both brake lights are working properly. (See Also: What Makes Brake Calipers Stick)
Key Points to Remember
* Always consult your owner’s manual for specific instructions and the correct bulb type for your 2017 Subaru Crosstrek.
* Be careful not to touch the glass of the new bulb with your bare hands, as this can shorten its lifespan.
* If you are unsure about any step of the process, it is always best to consult a qualified mechanic.
Replacing a brake light bulb on your 2017 Subaru Crosstrek is a simple task that can be completed in a short amount of time. By following these steps, you can ensure that your brake lights are always functioning properly and that you are driving safely.
Frequently Asked Questions
What type of brake light bulbs does a 2017 Subaru Crosstrek use?
The 2017 Subaru Crosstrek uses LED brake lights.
Where are the brake light bulbs located on a 2017 Crosstrek?
The brake light bulbs are located in the rear taillight assemblies. You’ll need to access them from the inside of the trunk.
How do I remove the old brake light bulb?
There’s usually a small access panel or cover on the taillight assembly. Remove this to access the bulb socket. The bulb should twist out counterclockwise. (See Also: How To Fix Brake Light On Dash)
How do I install the new brake light bulb?
Align the new bulb with the socket and twist it clockwise until it’s secure. Make sure it’s fully seated.
What should I do if my brake lights are still not working after replacing the bulb?
If the new bulb doesn’t fix the issue, there might be a problem with the wiring or the brake light switch. It’s best to consult a mechanic in this case.
